Dimensional Variation Modeling of Aircraft Compliant Part Assembly Considering Clamping Force Change

Compliant parts are widely applied to aircraft structures. Due to the ease of deformation of compliant parts in assembly,the prediction of assembly variation is especially important for assembly quality control. A dimensional variation model considering the clamping force change in assembly is proposed based on the method of influence coefficient(MIC). First,the assembly process is decomposed into several steps including positioning,clamping,joining,and spring-back. Then,the force-displacement relationship is formulated according to the varied force conditions on the parts in each assembly step. Finally,two examples are illustrated to validate the proposed assembly variation model. The results show the impact of clamping force change is significant on the assembly variation,and the proposed model can predict the assembly variation more accurately than the referred method without clamping force correction at the over-constrained locating points of fixture.     

空间核反应堆电源研究进展

随着航空航天领域对能源需求的不断扩大,核能的空间应用迎来了新的发展高潮。本文针对空间核反应堆技术的发展现状进行综述,重点关注了空间核反应堆与静态能量转换、动态能量转换技术结合供电的研究进展,总结分析了空间核反应堆电源技术的发展特点,并指出未来发展中需要重点关注的内容,为未来空间核反应堆电源的发展提供指导。     

翼身融合布局低速验证机前缘缝翼设计

翼身融合布局是未来民机最有可能实现的非常规布局形式，其气动布局方案的验证通常采用缩比模型飞行试验的方式进行。以某翼身融合布局低速验证机为研究对象，以数值计算方法为基础，分析了其在飞行试验中存在的纵向和横向不稳定现象，提出了改善的方案——增加前缘缝翼。对此验证机进行前缘缝翼的气动布局设计、典型翼型的二维前缘缝翼设计和机翼三维前缘缝翼的气动设计，利用数值计算方法对设计结果进行纵向和横向分析。结果显示，所设计的前缘缝翼可以明显地增大验证机的失速迎角，改善其纵向力矩特性和横向特性。     

基于EM‑EKF的深空光学自主导航系统光轴偏差补偿算法

在深空探测任务中,光学自主导航的精度受导航敏感器件安装精度的影响较大。提出了一种基于期望最大化-扩展卡尔曼滤波(EM-EKF)的光学自主导航系统光轴偏差补偿算法。算法基于条件概率的思想,预先设定状态变量和观测量的统计特性参数,通过不断地最大化条件期望,得到出现概率最大的状态变量估值和光轴偏差参数估值。该算法可分为4步:EKF、固定区间平滑、求解条件期望和期望最大化,不断迭代即可得到光轴偏差估计值。以火星探测近火段为例进行仿真验证,经光轴偏差补偿后,导航精度由100 km提升至20 km以内。     

一种基于参数控制的低轨星载接收机载波跟踪算法CSCD

低轨星座接收机面临大多普勒频移及频繁快速换星等设计约束,对其载波跟踪环路设计提出了较高的动态适应性与跟踪精度要求。针对以上问题,提出了一种基于参数控制的载波跟踪算法。该算法引入环路控制因子参数,将环路滤波器分为牵引和跟踪两阶段。基于理论建模推导环路控制因子的最优参数配置原则,指导实现牵引和跟踪两种状态滤波器的协同配合,在牵引阶段有效引导大多普勒信号快速入锁,在跟踪阶段精确估计载波频移参数,实现基于低轨星载平台的GNSS信号快速准确跟踪。理论与仿真结果均表明基于参数控制的载波跟踪算法能够有效提升环路的动态适应性与跟踪精度,满足低轨星载接收机的设计需求。与传统算法相比,该算法在保证信号跟踪精度的同时,能够将收敛时间缩短78%,且环路设计简单,易于硬件实现。     

侧板边界层对正激波/边界层干扰特性影响的数值模拟研究

为了研究外压式进气道处于临界工况时结尾正激波同时与压缩面和侧板上边界层的相互干扰,专门设计了三组具有不同前伸长度侧板的简化构型作为研究对象,利用数值模拟手段评估了侧板边界层厚度对正激波/边界层干扰特性的影响。仿真结果表明,当没有侧板边界层参与干扰时流动呈现较好的准二维特性,但当侧板边界层参与干扰后将形成较强的角区干扰结构,该角区三维干扰结构与对称面上的准二维干扰结构存在此消彼长的关系。此外,波系的空间形态也将由“准二维λ波”结构变为“双λ波+角区压缩波”结构,波系形态的改变则进一步导致壁面回流区分布以及摩擦力线拓扑结构变得更加复杂。     

动力涡轮导叶可调的三轴式船用燃气轮机动态实时仿真

鉴于传统的燃气轮机建模方法用于动力涡轮导叶可调的三轴式船用燃气轮机动态实时仿真时具有一定局限性,提出了一种新型的基于径向基函数(Radical basis function,RBF)的神经网络与部件法(Component modeling method,CMM)的复合建模方法 (HMRC)。该方法针对该型燃气轮机的结构和总体性能特点,合理地选取了样本点以减小样本规模。通过神经网络与部件法分别计算燃气发生器与动力涡轮相关参数,采用MATLAB/SIMULINK仿真软件建立实时仿真模型。与传统的部件法建立起来的仿真模型对比,新方法计算结果与部件法吻合度高,误差低于1%,同时模型的实时性得到了大幅提升,计算速度约为部件法的7倍。     

Dependence on forming parameters of an integral panel during the electromagnetic incremental forming process

Nowadays, more and more attentions are paid to electromagnetic incremental forming(EMIF), especially for a part with a large-scale size, e.g., an integral panel with stiffened ribs. In this work, the bending of a panel into a double-curvature profile via EMIF is carried out experimentally and evaluated by comparing the formed profile with the desired profile. During the process,discharges at four positions along different discharge paths are designed. The effects of forming parameters on the die-fittingness of the workpiece are discussed, for which two evaluation indices are used to judge forming results. The results show that a discharge voltage in an incremental mode is helpful to improve the fittingness and avoid the collision rebound against the die at the same time.Discharging at the diagonal positions with the ‘‘X" discharge path exhibits the minimal shape deviation and the best forming uniformity. On the contrary, discharging at the parallel positions with the ‘‘Z" discharge path obtains the worst forming quality. Overlap of the coil at different positions should be given during EMIF; however, a lower overlap rate of the coil helps improve the forming quality. The results obtained in this work are useful for forming integral panels with stiffened ribs via the EMIF process.     

径向进气系统设计探讨及实验研究

对于双轴压气机实验平台径向进气系统,为研究蜂窝器改善系统供气品质所发挥的作用,应用数值模拟对蜂窝器在进气道的布置位置进行研究,并应用五孔探针实验测量了含有蜂窝器的进气系统过渡段处的气动参数。模拟结果显示蜂窝器布置在弯头的前部及中部均能有效改善流动。实验测量结果显示气流偏航角小于2°,总压、静压及马赫数周向分布均匀,总压恢复系数大于98.3%。实验结果与模拟结果吻合较好,验证了数值研究方法的可信度和可靠性,同时也证明该进气系统的先进性。     

高超声速进气道/隔离段内流特性研究进展

作为超燃冲压发动机的增压部件,高超声速进气道/隔离段内部存在一系列的复杂流动现象,本文概述了该领域的相关研究进展。高超声速进气道/隔离段内存在多种激波/边界层干扰现象,并受到膨胀波系等的干扰,使其特性偏离了传统基于简化模型的研究结果,具有显著的三维干扰特征、多波组合干扰特征,并在通道内诱导出了显著的二次流,特别是角区旋涡流动。隔离段内存在复杂的激波和膨胀波结构,这些背景波系在隔离段内不断反射,形成显著的流向和横向参数间断。当出口流道发生几何或热力壅塞时,隔离段内会出现更为复杂的激波串现象。激波串和上游背景波系、角涡相干,呈现出明显的偏向性,并在前移过程中可能会出现两种特殊的动态前移过程。尽管最近对高超声速进气道/隔离段内流特性的认识得到了极大地提高,但仍然有较多的基础问题亟待解决。